|
Product - Castables |
Description |
| Morcocast Tab S-O |
A 90% alumina product for areas needing high abrasion
resistance, such as blow pipes. |
|
Morcocast Mul SF-O |
Used in the manufacture of precast shapes, forge furnace
car decks, car decks for ceramic kilns. |
| Morcocast Mul LC-O |
A mullite-based castable suitable for pumping or casting
tundish box safety linings, covers or any other applications
requiring thermal shock resistance and metal penetration. |
|
Morcocast 99 SF-O |
An extremely high Alumina content for tundish burner
assemblies, ladles impact pads, ladle wells and tundish
blocks. |
| Morcocast 85 SF-ULC-O |
This product is suitable for extreme service
applications including Delta sections, well blocks and ladle
bottoms. |
|
Morcocast 45-28 SF-O |
Used in the manufacture of precast shapes, boiler
applications, incineration (ash hoppers), furnace door jambs
and lintels, reheat furnaces, forge furnace car decks, coke
ovens and blast furnaces. |
| Morco Dura Floor |
A hot-floor product for casting tundish floors or any
other areas prone to metal and slag splash. |
| |
|
| Product - Gunning Mixes |
Description |
| Morcocast 60 Gun-O |
An all purpose 3,000°F gunning mix with low iron content
for areas where CO disintegration is a problem.
Re-heat furnace sidewalls and BOF hoods would be examples. |
|
Morcocast 55 HS-O |
For use in coke oven stand pipes and goose necks, coke
oven fill ports, blast furnace uptakes and down comers, and
dust catchers. |
| Morcocast 55 HS Gun-O |
For use in coke oven stand pipes and goose necks, coke
oven fill ports, blast furnace uptakes and down comers, and
dust catchers. |
|
Morcocast HS-O |
A 2,600°F service casting mix, where re-heat furnace
pre-heaters, coke oven quench-houses, or gunning areas are
subject to high alkaline environments. |
| Morcocast HSRC Gun-O |
A 2,600°F service gunning mix, where re-heat furnace
pre-heaters, coke oven quench-houses, or gunning areas are
subject to high alkaline environments. |
|
Morcocast Torpedo Gun |
Used in gunning torpedo cars. |
| Morco Grout 70-10 |
For grouting blast furnace stacks to maintain proper
thickness for skull formation. A special additive
allows for higher conductivity. |
| |
|
| Product - Insulating
Castables |
Description |
| Morcolite 50 X-O |
50lb./ft3 insulating castable. Low K
factor. Available in gun grade. Use for re-heat
furnace back-up linings. |
|
Morcolite 30 SF-O |
A 75-90lb./ft3 insulating castable for ladle
preheaters, ladle covers and re-heat furnace doors. |
| Morcolite 35-60 |
A 35 lb./cu.ft., 60% alumina insulating castable for
corrosion resistant duct work. |
|
Morcolite AS Grout |
A lightweight air-setting grout to be used in voids of
boilers or injectable hot repairs. |
| |
|
| Product - Plastics and
Ram Mixes |
Description |
| Morco Plastic 90 P GC |
For extreme service environments such as ramming around
well blocks, ladle fillets, ladle top rings and torpedo car
tops. |
|
Morco Plastic Mullite |
70% alumina, chemically bonded plastic to re-heat
furnace patching, ramming ladle and tundish wells. |
|
Morcoram LDV |
High alumina vibratable refractory for
back filling ladle safety linings. |
|
Morcoram Z-L |
For ramming tundish wells for long duration casting.
Zircon based, this product is also good for patching arc
furnace runners. |
| Morco Tite-Ram L |
For ramming tundish wells for short sequence casting. |
|
Morcoram Ladle-Level |
A dry refractory for a leveling base,
before ladle bricking in the ladle bottom. |
| |
|
| Product - Mortars and
Coatings |
Description |
| Morcoset 80 HW |
A heat set mortar of high Alumina content, ready to use
for laying high Alumina brick or coating mag-carbon,
alumina-carbon ladle brick, to prevent graphite oxidation on
new brick preheating. |
|
Morcoset 70 GC |
70% alumina, air setting mortar ready to use for ladle
and tundish back up brick, torpedo car brick. |
|
Morcoset S |
A 45% alumina, air setting mortar
ready to use for ladle and tundish back up brick, torpedo
car brick. |
|
Morcocoat 95 P |
A very viscous, extra high alumina,
chemically bonded mortar for high temperature patching and
bonding. |
| Morcoset 50 HW 50# |
50% alumina, heat setting mortar ready to use for ladle
nozzle to well block bonding. |
|
Morcocoat 93 PG |
Extra high alumina-graphite,
chemically-bonded mortar, ready to use for grouting blow
pipe into tuyre stock and collector nozzle bonding. |
